1. Technical and Compliance Services
TECHNICAL AND COMPLIANCE SERVICES
Providing technical engineering services specifically aimed at ensuring adherence to various government regulatory requirements. Our company offers expertise in navigating these complex regulations and providing the necessary technical support to achieve and maintain compliance, which can often be time-consuming and require specialized knowledge. Recognizing the critical importance of maintaining continuous compliance to avoid potential penalties and operational disruptions.
Our team has a deep understanding of the relevant regulatory frameworks and can provide tailored solutions to meet your unique needs.
Preparation and Processing of New Application and Renewal Application for the Permit to Operate (PTO) of the following Equipment:
- Pressure Vessel (DOLE OSH Rule 1170)
- Power Piping Lines
- Boiler
- Internal Combustion Engine
- Crane and Hoist
- Elevator and other related equipment
- Turbine (Steam, Hydro and
- Electrical Wiring Installation (EWI/CFEI)
Preparation and Processing of New Application and Renewal Application of the following:
- Building Permit and Occupancy Permit
- Structural / Civil Permit
- Fencing Permit
- Mechanical Permit to Install (MPTI) / Mechanical Permit to Operate (MPTO)
- Electrical Permit to Install (EPTI) / Electrical Permit to Operate (EPTO)
- Electronics Permit to Install (ELPTI) / Electronics Permit to Operate (ELPTO)
- Plumbing Permit / Sanitary Permit
Preparation and Processing of New Application and Renewal Application of the following:
- Environmental Compliance Certificate (ECC) Application
- Certificate of Non-Coverage (CNC) Application
- Discharge Permit
- Air Pollution Permit to Operate (PTO)
- Hazardous Wastes Generator Registration (HW ID)
- Hazardous Wastes Transporter Registration
- Preparation of Self-Monitoring Report (SMR) and Compliance Monitoring Report (CMR), Environmental Impact Statement (EIS), Initial Environmental Examination (IEE) and Environmental Performance Report (EPRMP)
Preparation and Processing of the following:
- LLDA Clearance (New Application, Exemption, Expansion, Amendment)
- Discharge Permit (New Application, Renewal, Revalidation, Indirect)
- Surface Water Clearance
- Shoreland Development Clearance
Preparation and Processing of the following:
- Fire Safety Evaluation And Inspection (FSEC)
- Fire Safety Compliance Report (FSCR)
- Fire Safety Compliance And Commissioning Report (FSCCR)
- Fire Safety Maintenance Report (FSMR)
- Fire Safety Inspection Certificate (FSIC)
Preparation and Processing of the following:
- Annual Energy Utilization Report (AEUR)
- Annual Energy Efficiency and Conservation Report (AEECR),
- Energy Audit Report (EAR) for your Designated Establishment(s)
- Energy Audit Level 1
- Energy Audit Level 2
For Compliance with Republic Act 11285 or the Energy Efficiency and Conservation (EEC) Act of 2019.
2. Engineering Services
Our company offers a comprehensive range of General Engineering Services. Our expertise encompasses Mechanical Works, including design, fabrication, installation, and maintenance; Electrical Works, covering power distribution, lighting systems, and control systems; Electronics Works, ranging from instrumentation to automation solutions; and Civil Works, such as structural design, building construction, and infrastructure development.
This broad range of capabilities allows us to cater to diverse engineering needs and provide integrated solutions for your projects.
Mechanical Works: Design, Fabrication, Supply, Installation and Repair of the following:
- Heating System
- Ventilation System
- Air-Conditioning System
- Fire Protection System
- Fire Suppression System
- Compressed Dry Air System
- Smoke Control System
- Refrigeration System
- Pressure Vessels
- Boiler System
- Internal Combustion Engine (ICE) – Generator Set and Fire Pump
- Piping System
Civil Works: Design, Fabrication, Supply and Installation of the following:
- Roofing Works
- Waterproofing Works
- Metal and Steel Works
- Painting Works
- Masonry Works
- Dry Wall Works
- Tile Works
- Welding Works
- Concrete Works
Electrical Works: Design, Fabrication, Supply, Installation, Repair and Modification of the following:
- First Private Pole
- Transformer (Oil Immersed and Dry-type)
- Current Transformer (CT) and Potential Transformer (PT)
- Switchgear
- Disconnect Switch
- Capacitor Bank
- Busduct System
- Lightning Protection System
- Surge Protection System
- Grounding System
- Cable Tray System
- Cable and Wires
Electronics Works: Design, Fabrication, Supply and Installation of the following:
- Closed Circuit Television (CCTV) System
- Paging System
- Fire Detection and Alarm System (FDAS)
- Telecommunication System
- Building Management System (BMS)
- Audio Visual System
- Accelerograph – DPWH Requirements
3. TESTING, COMMISSIONING AND MAINTENANCE SERVICES
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Ultrasonic Thickness Gauging (UTG) Test Method One of the widely used NDT techniques, Ultrasonic Thickness Gauging involves the use of high-frequency sound waves to measure the thickness of a material. This method is crucial for assessing the remaining thickness of components, aiding in detection of corrosion or erosion. In our company, we utilize the data obtained from UTG to compute essential metrics such as Minimum Thickness Required, Corrosion Rate, Projected Remaining Life, Maximum Allowable Working Pressure, Bursting Pressure and Factor of Safety as required by Department of Labor and Employment (DOLE) and Philippine Economic Zone Authority (PEZA). |
Magnetic Particle Inspection (MPI) Test Method
Magnetic Particle Inspection is utilized to detect surface and near-surface flaws in ferromagnetic materials. By inducing a magnetic field and applying iron particles, any discontinuities like cracks or voids can be easily identified, making it an effective tool for quality control.
Penetrant Test (PT) Method
The Penetrant Test, also known as Dye Penetrant Inspection, is employed for detecting surface-breaking defects in non-porous materials. It involves applying a liquid penetrant to the surface, which seeps into any surface cracks. Excess penetrant is then removed, and a developer is applied to reveal the flaw.
Hydrostatic Test Method
In the Hydrostatic Test, components are pressurized with a liquid, typically water, to ensure they can withstand the design pressure without leaking or deforming. This method is crucial for verifying the structural integrity of pressure vessels and pipelines.
Thermographic Inspection Method
Thermographic testing involves using infrared cameras to detect anomalies in the thermal patterns of mechanical equipment. Variations in temperature can indicate potential defects like overheating, making this method valuable for predictive maintenance.
Bubble Leak Test Method
The Bubble Leak Test, a type of leak detection method, is used to identify leaks or porosity in pressure vessels or piping systems. Components are pressurized, and a soapy solution is applied to the surface. Any gas leak is easily identified by the formation of bubbles.
Elevator
Elevators are indispensable in modern buildings, providing vertical transportation for people and goods. Load testing of elevators is crucial to ensure that they can safely carry their maximum rated load capacity without any issues. This testing involves simulating different weight loads to assess the elevator’s response and safety mechanisms under varying conditions. Regular load testing helps identify potential faults or weaknesses in the elevator system before they escalate into safety hazards.
Crane and Hoist
Cranes and hoists are essential equipment in construction, manufacturing, and logistics industries for lifting and moving heavy loads. Load testing of cranes and hoists involves applying loads that exceed the maximum weight they are designed to lift. This testing verifies the structural stability of the equipment, the accuracy of load indicators, and the performance of safety features such as limit switches and overload protection systems. Proper load testing ensures the safe operation of cranes and hoists, preventing accidents and equipment failures.
Heavy Equipment (Forklift, Lifter, etc.)
Heavy equipment used in the manufacturing process are subjected to extreme working conditions and heavy loads on a daily basis. This testing helps identify potential mechanical issues, such as fatigue failure or deformation, that could compromise the equipment’s operational efficiency and safety. By conducting load testing regularly, operators can optimize the maintenance and performance of heavy machinery, reducing downtime and enhancing productivity.
Thermographic Inspection
Thermal scanning is to detect any anomalies or potential issues within the electrical system that could lead to equipment failure, downtime, or even fire hazards. By capturing thermal images, technicians can identify hot spots caused by loose connections, overloading, or faulty components that are not visible to the naked eye.
Insulation Resistance (IR) Test Including Polarization Index (PI) and Dielectric Absorption Ratio (DAR)
The Insulation Resistance Test is used to assess the integrity of insulation in electrical systems and equipment. By measuring the resistance of insulation to the flow of current, this test helps to determine whether the insulation is in good condition or if there are any defects such as moisture, dirt, or age-related degradation.
Contact Resistance Test
Evaluating the resistance at electrical connections to identify and rectify loose or deteriorating contacts that can lead to power inefficiencies.
Winding Resistance Test
Verifying the resistance of transformer windings for optimal performance and longevity. Measuring the resistance of the windings assures that the connections are correct and the resistance measurement indicates that there are no severe mismatches or openings. Many transformers have taps built into them. These taps allow the ratio to be increased or decreased by fractions of a percent.
Transformer Turn Ratio (TTR) Test
Determining the turns ratio in transformers to confirm voltage regulation and efficiency.
Dissolved Gas Analysis (DGA)
Monitoring gases dissolved in transformer oil to detect incipient faults and insulation degradation.
Oil Dielectric Breakdown Voltage (DBV)
Measuring the breakdown voltage of insulating oils to prevent failures due to inadequate dielectric strength.
Transformer Oil Quality Analysis
Assessing the condition of transformer oil to maintain dielectric strength and thermal conductivity.
Ground Resistance Test / Earth Resistance Test
Ensuring effective grounding systems for electrical safety and equipment protection.
AC/DC/VLF Hi-Pot Test
Applying high voltage to detect insulation weaknesses and ensure electrical safety. For the Very Low Frequency (VLF), Assessing cable integrity and insulation conditions at low frequencies.
Circuit Breaker Trip Unit Test
Testing the trip units in breakers to guarantee proper operation during fault conditions.
Protective Relay Test
Protective relays are essential components in electrical systems that sense abnormalities, such as overloads, short circuits, or ground faults, and initiate appropriate actions to prevent damage to equipment and ensure personnel safety. The primary purpose of protective relay testing is to verify that these relays are functioning correctly and will operate as intended during fault conditions. By conducting periodic tests, you can identify any faulty relays, settings errors, or wiring issues, allowing you to take corrective actions before a fault occurs.
Power Quality Analysis (PQA)
Power Quality Analysis is to identify, evaluate, and mitigate power quality issues that can adversely affect electrical systems and sensitive equipment. By monitoring and analyzing key parameters such as voltage, current, harmonics, and frequency variations, Power Quality Analysis helps in diagnosing problems such as voltage sags, swells, transients, harmonics distortion, and flicker which can lead to equipment malfunction, downtime, and increased energy costs.
Leakage Reactance / Impedance Test
The Leakage Reactance and Impedance Test is essential in determining the parameters of transformers and electrical machines. These tests are conducted to evaluate the performance and efficiency of the equipment, ensuring proper operation under varying load conditions. By measuring the leakage reactance and impedance, engineers can assess the quality of insulation, detect any potential faults or defects, and optimize the design of the equipment for improved efficiency.
Current Transformer (CT) and Potential Transformer Analysis / Test
Validating the accuracy and performance of current and potential transformers.
Partial Discharge (PD)
Detecting partial discharges in electrical equipment to prevent insulation failures.
Excitation Current Test
a useful diagnostic testing for power transformers that can detect problems related to the core or windings
Insulation Power Factor and Capacitance Test
Used to measure dielectric losses, which relate the wetness, dryness or deterioration of transformer insulation
Contact Timing and Bounce Test
Checking the timing and contacts bounce in circuit breakers for efficient operation.
Saturation / Knee Point Test
Assessing transformer saturation to prevent core damage and ensure optimal performance.
Lightning Arrester Maintenance and Counter Test
to ensure it continues to protect electrical systems and structures from lightning strikes
Racking System Inspection and Load Testing
To assess the structural integrity of our racking systems and ensure they can safely support the intended loads. Prevents accidents, injuries, and damage to products. Our company conducts visual inspections, performs load testing as per manufacturer guidelines, and address any identified issues promptly.
Fire Protection System Testing and Maintenance
To verify the functionality of fire protection systems such as alarms, sprinklers, and extinguishers. Our company schedules regular testing, inspections, and maintenance by certified professionals to comply with fire safety regulations.
Heating, Ventilation and Air Conditioning System (HVAC) Maintenance
To maintain indoor air quality, regulate temperature, and ensure HVAC system efficiency. Enhances comfort for occupants and prolongs the lifespan of the equipment. Our company cleans the equipment, changes or clean air filters regularly, checks for leaks, calibrates thermostats, and schedules professional servicing as needed.
Electronics Testing and Maintenance
Our company provides testing and maintenance to the following system:
- Closed Circuit Television (CCTV) System
- Paging System
- Fire Detection and Alarm System (FDAS)
- Telecommunication System
Internal Combustion Engine (ICE) Maintenance – Generator Set and Fire Pump
To ensure reliable backup power in case of outages. Minimizes downtime and protects sensitive equipment. Our company tests generator functionality, changes oil and filters, inspect fuel levels, and follows maintenance schedules provided by the manufacturer.
Forklift Inspection and Maintenance
To verify the safe operation of forklifts and prevent accidents. Ensures the well-being of operators and maintains productivity. Our company checks brakes, tires, lights, and hydraulics, conducts regular inspections, and provides training for forklift operators.
Proposed Construction, Fabrication and Installation Drawing/Design Services
Our company specializes in preparing wide range proposed construction and fabrication drawings that are in-line with our client specific needs and requirements. We offer comprehensive drawings designed to guide and support the process
As-Built Drawing/Design Services
Our company provides accurate and detailed As-Built drawings upon project completion or for compliance with government regulation. Our team can prepare the following drawings:
- Architectural Drawings and Plans
- Structural Drawings and Plans
- Mechanical Drawings and Plans
- Electrical Drawings and Plans
- Electronics Drawings and Plans
- Fire Protection Drawings and Plans
- Sanitary Drawings and Plans
- Plumbing Drawings and Plans
Re-CAD Design Services
Our company offers professional re-CAD services to update and enhance existing drawings to meet current project requirements. Whether you need revisions, modifications, or conversions, our skilled CAD experts are here to ensure that our clients drawings are up-to-date and compliant with the latest industry standards.
Power System Analysis (PSA) or Electrical Design Analysis
Our company provides electrical design analysis for DOLE, PEZA and LGU Compliance with the scope of the following:
- Load Flow and Voltage Drop Calculations
- Short Circuit Analysis
- Protection Coordination Study
- Arc Flash Risk Assessment
- Power Quality Analysis
- Grounding Assessment
The Power System Analysis service offered by our company plays a crucial role in evaluating and optimizing the performance of electrical power systems. This involves studying the transmission, distribution, and utilization of electrical energy to ensure efficient and reliable power supply.
Hydraulic Calculation
Hydraulic Calculation services are vital for assessing fluid dynamics and optimizing the design of hydraulic systems. By analyzing the flow of liquids and gases in pipelines, pumps, and valves, we can identify potential bottlenecks and inefficiencies, leading to improved system performance.
Piping Flow and Pressure Drop Calculation
Our expertise in Piping Flow and Pressure Drop Calculation enables us to design and analyze complex piping systems effectively. By simulating fluid flow and pressure distribution within pipelines, we can identify areas of concern and propose solutions to enhance overall system efficiency.
Cooling Load Analysis
Cooling Load Analysis is a fundamental service for evaluating the thermal requirements of buildings and industrial facilities. By calculating the heat gain and loss within a space, we can determine the optimal cooling solutions to maintain comfortable indoor conditions while minimizing energy consumption.
Smoke Control System Analysis
Smoke Control System Analysis is essential for ensuring the safety and compliance of buildings with stringent fire protection regulations. Our detailed analysis of smoke extraction systems and ventilation strategies helps to create a safe environment in the event of a fire emergency.
For compliance of Fire Code of the Philippines Section 10.2.7.3 Smoke Control System
Structural Analysis
Structural Analysis is a cornerstone service that underpins the stability and integrity of buildings and infrastructure projects. By conducting comprehensive assessments of structural components and systems, we can identify vulnerabilities, mitigate risks, and enhance overall structural performance.
Safety, Reliability and Conformity Certification
Our company provides safety certification with visitation of our professional engineers for the following system:
- Mechanical System
- Electrical System
- Electronics System
- Structural System
- Plumbing System
- Sanitary System
Retainer and Consultancy Services
Our company specializes in providing retainer and consultancy services to clients across various industries.
- Professional Mechanical Engineer (PME), Professional Electrical Engineer (PEE), Professional Electronics and Communication Engineer (PECE)
- Registered Mechanical Engineer (RMEE), Registered Electrical Engineer (REE) and Registered Electronics and Communication Engineers (RECE)
- Registered Master Electrician (RME) and Certified Plant Mechanic (CPM)
- Certified Energy Manager (CEM) and Certified Energy Auditor (CEA)
Professional Engineers Consultation (Signing and Sealing Services)
Our professional and registered engineers provide signing and sealing of plans, analysis, reports and any related documents.
- Professional Mechanical Engineer (PME), Professional Electrical Engineer (PEE), Professional Electronics and Communication Engineer (PECE)
- Registered Civil Engineer (RCE)
- Registered Architect
- Registered Master Plumber (RMP)